2:37 Will connecting LED strips of varying lengths in parallel cause different levels of brightness? Roel Van de Paar
1:55 Electronics: EMI and reliability considerations for low-frequency, low-voltage DC load drive Roel Van de Paar
2:34 What do I connect the ground and power symbols in this schematic to? (2 Solutions!!) Roel Van de Paar
2:11 Electronics: Simple methods for switching a boost converter, to get a stable output voltage? Roel Van de Paar
3:51 Electronics: Limiting sensor input voltage without biasing measurement (4 Solutions!!) Roel Van de Paar
2:37 Electronics: Help explaining "reactive power" video: lights do not use any power? (3 Solutions!!) Roel Van de Paar
2:16 Electronics: Switch on and off a relay based on two different thermistor values (2 Solutions!!) Roel Van de Paar
2:16 Electronics: Why VDDIO is more than VDDcore supply in VLSI/ integrated chips? (3 Solutions!!) Roel Van de Paar
2:34 Electronics: Isn't the amplification in amps always going towards infinity? (3 Solutions!!) Roel Van de Paar
2:51 MCU GPIO input pin state copying/buffering as another pin output in real-time? (2 Solutions!!) Roel Van de Paar
2:16 Electronics: How do I make an integrator to always output LOW and output HIGH only when needed? Roel Van de Paar
3:21 Electronics: How do I calculate how long my robot's battery will last? (2 Solutions!!) Roel Van de Paar
5:04 Electronics: Why do they place the graph of the input voltage in such a slanted way? Roel Van de Paar
3:16 Electronics: Pulling the circuit's voltage to the ground with grounded probe (2 Solutions!!) Roel Van de Paar
2:00 Why are shunt resistors in BLDC motor drivers placed betweent MOSFETs and ground and not MOSFETs... Roel Van de Paar
2:40 Why does making this change to my DHT11 code cause it not to work? (2 Solutions!!) Roel Van de Paar
2:08 Do 4 batteries capable of outputting 0.5 A in parallel give the batteries a max output of 2 A? Roel Van de Paar
2:36 Electronics: What is the purpose of the anti-parallel diodes in this Wien Bridge oscilator circuit? Roel Van de Paar
1:31 Overcharge a sealed 12V lead-silver-calcium battery with a power supply to prevent sulphatation Roel Van de Paar
2:23 Why the integrations of left and right domain are not done and be said enough to calculate the... Roel Van de Paar
4:02 Electronics: Current source - Achieving a defined settling time with variable load resistance Roel Van de Paar
3:48 Failed to get desired output of a pulse width modulation circuit simulation (2 Solutions!!) Roel Van de Paar
3:07 Electronics: H-Bridge: forward and backward dc motor with ic 555 by esp8266 gpio Roel Van de Paar
2:45 Electronics: Driving Multiple Balanced Audio Runs Off Single Differential Op-Amp Circuit Roel Van de Paar
2:08 Electronics: Why not use integral for averaging inductor current? (2 Solutions!!) Roel Van de Paar
3:38 Electronics: Why emitter follower is so noisy and distorted in large signal? (4 Solutions!!) Roel Van de Paar
3:02 Electronics: Why can't we use magnets to create energy like this? (3 Solutions!!) Roel Van de Paar
2:11 Electronics: Possible outcomes of not using a current limiting resistor in this LED driver? Roel Van de Paar
1:50 Codec in 'master mode' require more than one external clock? (MCLK?) to drive I2S system timing... Roel Van de Paar
2:14 What is the best way to parallel two shunt resistors using a switch? (2 Solutions!!) Roel Van de Paar